datasheet panel mount h16wd series ? r a t i ngs f r o m 25a to 90a @ 48-690 v a c ? 1600 volts blocking ? scr output for heavy industrial loads ? zero turn-on or instantaneous turn-on outputs ? ul/csa/vde approved, ce compliant to en60950-1 ? improved sems screw and washer ? redesigned housing with anti-rotation barriers for generation 3 datasheet click here ? dc control ? direct bond copper substrate ? emc compliant to level 3 ? direct power lead frame ? epoxy free design product selection 90a 75a 50a 25a control voltage 4-32 vdc H16WD6025 h16wd6050 h16wd6075 h16wd6090 available options thermal pad blank: not included h: included series transient overvoltage 6wd: 1600 vpk rated load current 25: 25 amps 50: 50 amps 75: 75 amps 90: 90 amps switching type blank: zero voltage turn-on -10: instantaneous turn-on (6) input status led blank: not included g: included termination blank: screw f: quick connect (5) k: round standoffs operating voltage 60: 48-690 vac 60 h1 25 k g h -10 6wd required for valid part number for options only and not required for valid part number output specifications (1) description 25a 50a 75a 90a operating voltage (47-440hz) [vrms] 48-690 48-690 48-690 48-690 transient overvoltage [vpk] 1600 1600 1600 1600 rated load current [arms] (2) 25 50 75 90 rated load current {ul508 motor controller} [arms] (2) 10 20 30 45 minimum load current [marms] 150 150 150 150 maximum off-state leakage current @ rated voltage [marms] 1.0 1.0 1.0 1.0 minimum off-state dv/dt @ maximum rated voltage [v/sec] 500 500 500 500 maximum 1 cycle surge current (50/60hz) [apk] 239/250 597/625 954/1000 1145/1200 maximum i2t for fusing (50/60hz) [a2 sec] 285/259 1779/1621 4555/4150 6560/5976 thermal resistance junction to case (rjc) [c/w] 0.8 0.45 0.3 0.27 maximum on-state voltage drop @ rated current [vrms] 1.3 1.3 1.2 1.2 hp rating ul 508/iec60947[hp (kw)]: 240 vac 1.5 (1.1) 3 (2.2) 5 (3.7) 7.5 (5.6) hp rating ul 508/iec60947[hp (kw)]: 380 vac 2 (1.5) 5 (3.7) 7.5 (5.6) 15 (11.2) hp rating ul 508/iec60947[hp (kw)]: 480 vac 3 (2.2) 5 (3.7) 10 (7.4) 20 (14.9) hp rating ul 508/iec60947[hp (kw)]: 600 vac 3 (2.2) 10 (7.4) 15 (11.2) 25 (18.6) minimum power factor (at maximum load) 0.5 0.5 0.5 0.5 do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount input specifications (1) description dc control control voltage range (3) 4-32 vdc must turn-off voltage 1 .0 vdc maximum reverse voltage 32 vdc minimum input current @ minimum voltage (for on-state) 7ma maximum input current @ maximum voltage 12ma nominal input impedance current regulated maximum turn-on time [msec] (4) 1/2 cycle maximum turn-off time [msec] 1/2 cycle led input status indicator w/?g? option (green) general specifications (1) description parameters dielectric strength, input/output/base (50/60hz) 4000 vrms minimum insulation resistance (@ 500 vdc) 10 9 ohm maximum capacitance, input/output 8 pf ambient operating temperature range -30 to 80 c ambient storage temperature range -40 to 125 c weight (typical) 2.6 oz (74.9 g) housing material ul 94 v-0 ssr mounting torque range [in lbs/nm] 18-20 (2-2.2) baseplate material aluminum input terminal screw torque range [in-lbs/nm] 13-15 /1.5-1.7 output terminal screw torque range [in lb/nm] 18-20 (2-2.2) ssr mounting screw torque range [in-lbs/nm] 18-20 / 2.0-2.2 humidity 85% non-condensing wiring diagram ac v load (8) 1 ( ) 2 ( ) 1 2 output s oli d s t a t e r ela y 4 3 input 4 (? ) 3 (+ ) recommended wire sizes terminals wire size (solid / stranded) wire pull-out strength (lbs)[n] input output 24 awg (0.2 mm 2 ) / 0.2 [minimum] 2 x 12 awg (3.3 mm 2 ) / 3.3 [maximum] 20 awg (0.5 mm 2 ) / 0.518 [minimum] 2 x 10 awg (5.3 mm 2 ) / 5.3 2 x 8 awg (8.4 mm 2 ) / 8.4 [maximum] 10 [44.5] 90 [400] 30 [133] 110 [490] 90 [400] input current vs input voltage standard regulated ?dc? inputs input current (ma) 25 20 15 10 5 0 dc input voltage 0 5 10 15 20 25 30 +dc - dc ac trigger circuit current limiter ac 3 4 2 1 (7) equivalent circuit block diagram do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount mechanical specifications (1) screw termination 1 output 2 s oli d s t a t e r ela y 4 input 3 1.1 [27.9] 0.49 [12.4] mounting hole/slot 0.18 [4.5] dia. 0.89 [22.6] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] 1.0 [25.4] 1.75 [44.5] mounting hole/slot r 0.09 [2.2] 0.92 [23.3] round standoff termination (?k? option) 1 output 2 s oli d s t a t e r ela y 4 input 3 1.1 [27.9] 0.49 [12.4] mounting hole/slot 0.18 [4.5] dia. 1.08 [27.5] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] 1.0 [25.4] 1.75 [44.5] mounting hole/slot r 0.09 [2.2] 0.89 [22.6] quick connect termination (?f? option) - up to 25 amp (5) 1 output 2 s oli d s t a t e r ela y 4 input 3 mounting hole/slot 0.18 [4.5] dia. 1.1 [27.9] 0.49 [12.4] 8-32 output screw (2 places) faston terminal 0.25 x 0.032 (2 places) 1.31 [33.4] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] mounting hole/slot r 0.09 [2.2] 1.0 [25.4] 1.75 [44.5] 6-32 input screw (2 places) faston terminal 0.187 x 0.032 (2 places) 0.89 [22.6] 1.25 [31.8] quick connect termination (?f? option) - up to 50 amp (5) 1 4 2 3 s oli d s t a t e r ela y output input mounting hole/slot 0.18 [4.5] dia. 1.1 [27.9] 0.49 [12.4] 8-32 output screw (2 places) faston terminal 0.25 x 0.032 (4 places) 1.31 [33.4] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] mounting hole/slot r 0.09 [2.2] 1.0 [25.4] 1.75 [44.5] 6-32 input screw (2 places) faston terminal 0.187 x 0.032 (2 places) 0.89 [22.6] 1.25 [31.8] general notes (1) all parameters at 25c unless otherwise speci?ed. (2) heat sinking required, see derating curves. (3) increase minimum voltage by 1v for operations from -20 to -30c. (4) turn-on time for instantaneous turn-on versions is 0.02 msec. (5) single pair (up to 25a) double pair* (50a model only). *caution: user must connect to both pairs. (6) instantaneous turn-on version is not recomended for capacitive loads. use zero turn-on only. (7) elective input status led, ?g? option. (8) load can be wired to either ssr output terminal 1 or 2. do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount surge current information 0 50 100 150 200 250 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 25 a 0 100 200 300 400 500 600 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 50 a 0 100 200 400 300 500 600 700 900 800 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 75 a 0 150 450 300 600 750 900 1200 1050 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 90 a non repetitive peak surge current at tj initial 40oc. thermal derate information 25 20 15 10 5 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 25 a 1.5oc/w 2oc/w 3oc/w 50 40 30 20 10 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 50 a 0.7oc/w 1oc/w 1.5oc/w 2oc/w 75 60 45 30 15 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 75 a 0.5oc/w 0.7oc/w 1oc/w 1.5oc/w 80 90 70 50 30 10 60 40 20 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 90 a 0.5oc/w 0.7oc/w 1oc/w 1.5oc/w do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount agency ap provals designed in accordance with the requirements of iec 62314 iec 61000-4-2 : electrostatic discharge ? level 3 iec 61000-4-4 : electrically fast transients ? level 3 iec 61000-4-5 : electrical surges ? level 3 iec 600068-2-6: vibration 0.33mm and 0.75mm amplitude over 10-55 hz iec 600068-2-27: shock resistance 15g/11ms e116949 acc e s o r i e s new accessories! protective cover & hardware kits protective cover part number: ks101 clear plastic cover compatible with all new s1 designs. safety covers provide added protection from electric shock when installing or checking equipment. hardware kit part number: hk3 bag with 2 threaded standoffs, 2 screws 8-32 x 1/4, and 2 lockwashers m8 for output, and 2 threaded standoffs, 2 screws 6-32 x 3/16, and 2 lockwashers m6 for input. standoff screws provide additional mounting options such as "dead bug" mounting, using lug terminals or wire terminals to the side of the relay. hardware kit part number: hk4 bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. used to mount tmr1 lug terminals. recommended accessories cover hardware kit heat sink part no. thermal resistance [oc/w] lug terminal thermal pad ks101 hk1 hk3 hk4 hs501dr hs301 / hs301dr hs251 hs201 / hs201dr hs172 hs151 / hs151dr hs103 / hs103dr hs072 hs053 5.0 3.0 2.5 2.0 1.7 1.5 1.0 0.7 0.5 trm1 trm6 hsp-1 hsp-2 rev. 082813 do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount danger / peligro / danger /gefahr / pericolo / h a z a r d o f e l e ct ric s ho ck, e x p l o s io n, o r a r c flash. ? di s c o n n e c t a l l p o w e r b e f o r e i n s ta l l i n g o r wo r k i n g w i t h th i s equipment. ? v e r i f y a l l c o n n e c ti o n s a n d r e p l a c e a l l c o v e r s b e f o r e tu r n i n g o n p o w e r . f a ilu r e t o f o llo w t h e s e in s t r u c t io n s w ill r e s u lt in d e a t h o r s e r io u s in ju r y . rie s g o de de s c a rg a e l e ct ric a o e x p l o s io n. ? de s c o n e c ta r to d o s l o s s u m i n i s tr o s d e e n e r g i a a e s te e q u i p o a n t e s d e tr a b a j a r c o n e s te equipo. ? v e r i f i c a r to d a s l a s conexiones y colocar todas l a s ta p a s antes d e energizer el e q u i p o . e l in c u m p lim ie n t o d e e s t a s in s t r u c c io n e s p u e d e p r o v o c a r la m u e r t e o le s io n e s s e r ia s . ris q u e de de s ch a rg e e l e ct riq ue o u explosion ? e te i n d r e to u te s l e s s o u r c e s d ' n e r g i e d e c e t a p p a r e i l a v a n t d e tr a v a i l l e r d e s s u s d e c e t a p p a r e i l ? vrifier tous connections, et remettre tous couverts en olace avant de mettre sous de n o n-s u iv i d e c e s in s t r u c t io n s p r o v o q u e r a la m o r t o u d e s l s io n s srieuses s r i e u s e s. g e f a hr e in e s e l e kt ris ch e n s chl a g e s o de r e ine r e x p l o s io n. ? s te l l e n s i e j e g l i c h e n s tr o m a b , d e r d i e s e s g e r ? t v e r s o r g t, bevor s i e a n dem g e r ? t arbeiten d u r c h f h r e n ? v o r d e m dr e h e n a u f e n e r g i e a l l e a n s c h l s s e b e r p r f e n u n d a l l e a b d e c k u n g e n e r s e t z e n. un t e r la s s u n g d ie s e r a n w e i s u n g e n k ? n n e n z u m t o d e o d e r z u s c h w e r e n v e r le t z u n g e n f h r e n. ris chio di s co s s a e l e t t ric a o de l l ?e s p l o s i o ne . ? s p e n g a tu tt a l ' a l i m e n ta z i o n e c h e f o r n i s c e q u e s ta a p p a r e c c h i a t u r a p r i m a d e l l a v o r a r e a questa a p p a r e c c h i a t u ra ? v e r i f i c a r e t u tti i c o l l e g a m e n ti e s o s ti tu i r e tu tte l e coperture p r i m a d e l l a r o ta z i o n e s u l l ' a l i m e n ta z i one l ' o m is s io n e d i s e g u ir e q u e s t e is t r u z io n i p r o v o c h e r l a m o r t e o d i le s io n i s e r i e ? ? ? ? ? ?? ??? ? ??? ? warning / avertissement / warnung /advertencia / avvertenza / / risk of material damage and hot enclosure ? the product's side panels may be hot, allow the product to cool before touching. ? follow proper mounting instructions including torque values. ? do not allow liquids or foreign objects to enter this product. failure to follow these instructions can result in serious injury, or equipment damage. risque de dommage materiel et de surchauffe du boitier ? les panneaux latraux du produit peuvent tre chauds. laisser le produit refroidir avant de le toucher. ? respecter les consignes de montage, et notamment les couples de serrage. ? ne pas laisser pntrer de liquide ni de corps trangers l'intrieur du produit. le non-respect de cette directive peut entra?ner, des lsions corporelles graves ou des dommages matriels. die nichtbeachtung dieser anweisung kann k?rperverletzung oder materialsch?den zur folge haben. gefahr von materialsch?den und geh?useerhitzung ? die seitenw?nde k?nnen hei? sein. lassen sie das produkt abkhlen, bevor sie es berhren. ? beachten sie die montageanweisungen, ? fhren sie keine flssigkeiten oder fremdk?rper in das produkt ein. si no se respetan estas precauciones pueden producirse graves lesiones, da?os materiales. riesgo de da?os materiales y de sobrecalentamiento de la unidad ? los paneles laterales del producto pueden estar calientes. esperar que el producto se enfre antes de tocarlo. ? respetar las instrucciones de montaje, y en particular los pares de apretado. ? no dejar que penetren lquidos o cuerpos extra?os en el producto. la mancata osservanza di questa precauzione pu causare gravi rischi per l'incolumit personale o danni alle apparecchiature. rischio di danni materiali e d'involucro caldo ? i pannelli laterali dell'apparecchio poss ono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. ? seguire le istruzioni di montaggio corrette. ? non far entrare liquidi o oggetti estranei in questo apparecchio. ??? ??? ???? ? ?????? ? ? ?????? ? ??? do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
datasheet panel mount annex - e n v i romental information the environmental information disclosed in this annex including the eip pollution logo are in compliance w i th people?s republic of china electronic industr y standard sj/t11364 ? 2006, marking for c ontrol of pollution caused by electronic information products. part name toxic or hazardous substance and elements lead mercury cadmium hexavalent polybrominated polybrominated (pb) (hg) (cd) chromium (cr (vi)) biphenyls (pbb) diphenyl ethers (pbde) semiconductor die solder ?q ? n?q
?s
u ?0? ? ?ms ????? |
? ?s0?<s 4 + 5
0? ? ? e?s
m1 p b ??? ? ? (pb) (hg) (cd) (cr (vi)) (pbb) (pbde) ?? ? 50 do not forget to visit us at: www.crydom.com copyright ? 2013 crydom inc. specifications subject to change without notice.
|
